Universal Waste Under 40 CFR Part 273: The Aerosol Can Rule Your State May Not Have Adopted
EPA added aerosol cans to the universal waste program in 2019 and authorized states never had to follow. What 40 CFR Part 273 requires, and what to check.
EPA added aerosol cans as the fifth universal waste stream in 40 CFR Part 273 through a final rule published at 84 FR 67202 on December 9, 2019, effective February 7, 2020. Seven years on, a maintenance supervisor in Wichita or Tulsa who read that rule and moved the spent can drum onto the universal waste track may be managing a fully regulated hazardous waste under the program the plant actually answers to.
The rule says so itself. Section VII.A states that “Authorized states are required to modify their programs only when EPA enacts Federal requirements that are more stringent or broader in scope than existing Federal requirements,” and that “authorized states may, but are not required to, adopt Federal regulations … that are considered less stringent than previous Federal regulations.” Section VII.B is blunter: “This final rule will be less stringent than the current Federal program,” and “Because states are not required to adopt less stringent regulations, they will not have to adopt the universal waste regulations for aerosol cans, although EPA encourages them to do so.” No adoption deadline applies.
EPA’s own state universal waste program table, updated October 8, 2026, shows what that produced across the six states iSi works in most. All six have adopted the universal waste rule. Only three carry a mark in the Aerosol Cans column: Missouri, Texas and Colorado. Kansas, Nebraska and Oklahoma are blank. That table is evidence of a gap, and it is not a reading of anyone’s state code. This research read EPA’s table and the federal rule. It did not read the Kansas, Nebraska or Oklahoma regulatory text, which is the only authority that answers the question. Verify against your state’s citation before managing cans as universal waste.
The 2019 rulemaking narrative is covered separately in our post on EPA’s final aerosol can universal waste rule. The rest of Part 273 is what most facilities never look at closely.
What the Reduced Requirement Track Actually Keeps
Part 273 was promulgated at 60 FR 25542 on May 11, 1995 and has been amended seven times, most recently by the aerosol can rule. 40 CFR 273.1(b) states what it does: it “provides an alternative set of management standards in lieu of regulation under” 40 CFR parts 260 through 272. The five covered streams at 273.1(a) are batteries (273.2), pesticides (273.3), mercury-containing equipment (273.4), lamps (273.5) and aerosol cans (273.6). A material has to already be a hazardous waste to be a universal waste, and every applicability section excludes material that is not yet waste and material that is not hazardous waste.
The authority is RCRA at 42 U.S.C. 6922, 6923, 6924, 6925, 6930 and 6937. “Hazardous waste” carries its ordinary Part 261 meaning here, so a stream that neither exhibits a Part 261 Subpart C characteristic nor contains a Subpart D listed substance is not a universal waste no matter which of the five categories it resembles. Aerosol cans carry two further applicability lines worth knowing: 273.6(b)(3) excludes a can that already meets the empty-container standard at 40 CFR 261.7, and 273.6(c) fixes the moment the can becomes waste, a used can on the date it is discarded and an unused can on the date the handler decides to discard it. That second date is the one a plant cannot reconstruct afterward, which is why the can-return policy and the accumulation clock belong in the same written procedure.
The five categories also reach further than their names suggest. Batteries come off forklifts, UPS systems, security panels and hand tools. Mercury-containing equipment is any device containing elemental mercury integral to its function, which still means thermostats, older HVAC controls, manometers and switches. Lamps means the bulb or tube portion of any electric lighting device, and 273.9 names fluorescent, high intensity discharge, neon, mercury vapor, high pressure sodium and metal halide. Aerosol cans means a non-refillable receptacle holding a gas compressed, liquefied or dissolved under pressure and fitted with a self-closing release device, which describes the maintenance crib at every plant in the region. Pesticides reach agricultural operations, grounds maintenance and anyone holding recalled or unused product. Between them the five streams put nearly every manufacturing plant, warehouse, hospital, school district, municipality, utility and large commercial building inside Part 273.
Two carve-outs come up constantly. 273.2(b) routes spent lead-acid batteries being reclaimed to Part 266 Subpart G instead, so the forklift battery going back to a vendor for reclamation is not on this track at all. And 273.8 lets a facility fold household and very small quantity generator waste of the same type into its universal waste management at its option, with the consequence that mixing them makes the combined waste subject to Part 273. A municipal collection box that takes residential batteries alongside the building’s own is using that option whether or not anyone wrote it down.
The structure is four roles. Subpart B covers small quantity handlers at 273.10 through 273.20, Subpart C large quantity handlers at 273.30 through 273.40, Subpart D transporters at 273.50 through 273.56 and Subpart E destination facilities at 273.60 through 273.62. A person who treats, disposes of or recycles universal waste falls outside the handler definition, except for the activities permitted at 273.13(a), (c) and (e) and 273.33(a), (c) and (e). Outside those, an on-site crushing operation becomes a destination facility, which pulls in parts 264, 265, 266, 268, 270 and 124 plus RCRA section 3010 notification under 273.60(a). A person engaged in off-site transportation, including the operator of a transfer facility, is not a handler either, which is why Subpart D stands as its own role rather than as a handler obligation.
EPA’s own summary of the track is that universal waste may be “stored for a year and … not required to be shipped with a manifest,” and that is true as far as it goes. What stays in place is a labeling rule with prescribed words, a date-proof rule with six named methods, two different training standards, a three-destination shipping restriction with a prior-agreement condition, a ten-day transfer facility limit and three years of records for large quantity handlers. Each is cheap to comply with and cheap to miss, and four of them attach at the 5,000 kilogram line rather than at the front door: notification and the EPA identification number, the stricter training standard, shipment record keeping and the labeling variants.
Am I a small quantity handler or a large quantity handler of universal waste?
The line is 5,000 kilograms, calculated collectively across batteries, pesticides, mercury-containing equipment, lamps and aerosol cans, measured at any time, per 40 CFR 273.9. Cross it once and large quantity handler status is retained through the end of that calendar year, even if the accumulation drops back down immediately.
“Collectively” means a battery program at 1,200 kilograms, a lamp retrofit staged at 2,600 and a can drum at 400 are one number. “At any time” means the measurement is instantaneous, so the highest accumulation the facility ever held decides the class. A lamp retrofit, a forklift battery changeout or a controls job that pulls mercury switches out of a building is how a plant usually crosses without a decision being made. The peak lasts a week while a contractor stages material, and the designation stays until December 31. Notification under 273.32(a)(1) is due before the limit is exceeded, so a facility that finds the crossing afterward cannot cure it on the original timeline.
Role rather than industry decides which subpart applies. A generator of universal waste is a handler, and so is the owner or operator of a facility, including all contiguous property, that receives universal waste from other handlers, accumulates it and sends it on. A corporate consolidation site is therefore a handler in its own right with its own 5,000 kilogram arithmetic, and the kilograms it takes in from sister plants count toward its own class rather than staying on the books of the plant that generated them.
Does a universal waste handler need an EPA identification number?
Only large quantity handlers. 273.32(a)(1) requires written notification sent and an EPA identification number received before meeting or exceeding the 5,000 kilogram limit. 273.12 states small quantity handlers are not required to notify. A handler already holding an identification number from a prior notification need not renotify, per 273.32(a)(2).
273.32(b) asks for the handler’s name and mailing address, the name and business telephone number of a site contact, the address or physical location where the waste is handled, a list of the universal waste types managed, and a statement that the handler is accumulating more than 5,000 kilograms at one time. The facilities that get caught have no prior notification at all, such as a school district or a distribution warehouse that crosses 5,000 kilograms during one lighting project. iSi’s own engagement history here is a fair picture of the spread: three engagements across two clients in 2020, a municipality and a mineral processing plant. Neither is the kind of site that thinks of itself as a hazardous waste facility.
What exactly must a universal waste container say?
One of three prescribed variants per stream, per 273.14 and 273.34: “Universal Waste Battery(ies),” “Waste Battery(ies)” or “Used Battery(ies),” with the same three-way pattern for lamps, mercury-containing equipment, mercury thermostats, pesticides and aerosol cans. The rule prescribes the words. Improvised labels are a finding.
A drum lettered “Spent Bulbs” fails a requirement that would have cost nothing to meet. For pesticides, the printed wording at 273.14 differs from 273.34 in its punctuation, so copy the text out of the section that matches your handler class rather than from the other one or from memory. This is the finding an inspector can make from the aisle, and a state agency will write it up on a single container. What that looked like when it happened, including the appeal that followed, is in our citation case study on a fluorescent lamp violation, which owns that story. Label text comes out of the CFR rather than from house style.
How does a facility prove how long universal waste has been accumulating?
273.15(c) gives six acceptable methods: the earliest date marked on the container, a date on each item, an on-site inventory with each item’s date, an on-site inventory with the earliest date in a group, a designated area marked with the earliest date, or any other method that clearly demonstrates the length of accumulation. Pick one and run it consistently.
The sixth method is the one people hear and the first five are the ones that survive an inspection, because the burden of demonstrating sits with the handler. A plant that dates some drums, keeps an inventory for others and marks the area for the rest has three partial records and no answer when an inspector picks a container. A fixed signed accumulation area is the easiest of the six to audit.
Can universal waste be held longer than one year?
Yes, but only on one ground. 273.15(b) and 273.35(b) permit longer accumulation solely to accumulate the quantities necessary to facilitate proper recovery, treatment or disposal, and they put the burden of proof on the handler. The default clock at 273.15(a) runs one year from the date generated or received.
Waiting for a recycler’s minimum load sits inside that ground. Waiting for next year’s capital budget, waiting on a vendor decision, or simply not having moved the drum sit outside it, and 273.15(b) means the handler produces the evidence. The clock runs from generation or receipt rather than from the date the container was filled. How that clock interacts with the in-plant route for lamps and batteries specifically, including the handoffs between shifts and vendors, is covered in our post on in-plant waste movement in a manufacturing plant.
What training do employees who handle universal waste actually need?
Two different standards. 273.16 requires a small quantity handler to inform employees who handle or manage universal waste of proper handling and emergency procedures. 273.36 requires a large quantity handler to ensure employees are thoroughly familiar with those procedures relative to their responsibilities during normal operations and emergencies.
“Inform” is a one-direction obligation that a toolbox talk and a sign-in sheet can satisfy. “Ensure thoroughly familiar” asks the handler to show the employee knows the procedure, which is a competence test rather than a delivery test. Both scope content to the waste types the employee handles and to that employee’s responsibilities, and neither names a frequency, a duration or a written test.
Does a universal waste shipment need a manifest or shipment records?
No manifest. 273.19 states a small quantity handler is not required to keep records of universal waste shipments at all. 273.39 requires a large quantity handler to record every shipment received and sent, with counterparty name and address, quantity by type and date, retained at least three years.
273.39(a) covers shipments received and 273.39(b) shipments sent, each capturing the other party’s name and address, the quantity of each type of universal waste, and the date of receipt or departure. 273.39(c) runs retention from the date of receipt for incoming records and from the date of departure for outgoing ones, so a log kept by calendar month without quantities by type does not meet it. Destination facilities carry their own version at 273.62, three years from the date of receipt, and with no manifest in the file that record is the only paper trail the shipment leaves.
Where may a facility legally send its universal waste?
Three destinations only, per 273.18(a) and 273.38(a): another universal waste handler, a destination facility, or a foreign destination. 273.18(d) requires the receiving handler’s agreement before the shipment is sent, and 273.18(c) applies the full 49 CFR 172 through 180 hazardous materials rules to anything meeting a DOT hazardous material definition.
The prior agreement at 273.18(d) is the condition most often skipped, because a handler-to-handler transfer feels like an internal move. A multi-site operator consolidating lamps into one regional staging building is a handler shipping to a handler, and the receiving site has to have agreed. Rejected loads have their own path at 273.18(e) and (f), and 273.18(g) requires a handler who receives a shipment containing hazardous waste that is not universal waste to immediately notify the appropriate EPA regional office. Universal waste status under RCRA also says nothing about hazardous material status under 49 CFR, and a drum of pressurized cans carries marking, labeling, shipping paper and placarding duties.
How long can a transporter hold universal waste at a transfer facility?
Ten days or less, per 273.53. Beyond ten days the transporter becomes a universal waste handler subject to Subpart B or Subpart C. 273.18(b) makes a facility that hauls its own universal waste a transporter, so a plant running its own truck inherits this limit.
A plant that sends its own box truck from a satellite warehouse to the main site has made itself a universal waste transporter under Subpart D for that movement, and any point where the material sits in transit is a transfer facility on a ten-day clock.
Can a facility puncture and drain its own aerosol cans?
Yes, under conditions. 273.13(e) and 273.33(e) require a device designed for the purpose, a written procedure, the manufacturer’s specification kept on site, trained operators, transfer of contents into a container meeting the applicable requirements, a hazardous waste determination on what comes out, and a written spill or release procedure with a clean-up kit available.
Work outside those conditions is treatment, which puts the facility into destination facility territory and the Part 264 or 265 permitting that comes with it. Two of the seven get missed most often. The manufacturer’s specification for the puncturing device has to be on site, meaning the paperwork that came with the unit belongs in the compliance file rather than with the vendor. And the contents that come out require a hazardous waste determination in their own right, because the drained liquid is a new waste stream. All of it assumes the state program covers aerosol cans in the first place.
Which universal wastes does my state’s program actually cover?
Not all five everywhere. EPA’s state table, updated October 8, 2026, shows all six states in iSi’s region have adopted the rule, but the Aerosol Cans column is marked only for Missouri, Texas and Colorado. Kansas, Nebraska and Oklahoma are blank. Verify the state citation before managing a can as universal waste.
That matters because of RCRA authorization. In an authorized state the state’s own adopted text is the operative program, so the federal list of five streams is not the operative list everywhere. EPA’s universal waste page, updated September 18, 2026, puts it generally: “The majority of states have adopted the full federal universal waste program, however, others have only adopted some of the federal universal wastes.”
| State | State citation as printed | Adopted | Authorized | Aerosol cans per EPA’s table | State additions |
|---|---|---|---|---|---|
| Kansas | 28-31-15; 28-31-273 | Yes | Yes | blank | |
| Missouri | 10 CSR 25-16.273 | Yes | No | marked | |
| Nebraska | Ch. 25, Title 128 | Yes | Yes | blank | Electronics |
| Oklahoma | 252:205-3-2; 252:205 | Yes | Yes | blank | |
| Texas | 30 TAC 335, Subchapter H, Division 5 | Yes | Yes | marked | Paint and paint-related wastes |
| Colorado | 6 CCR 1007-3 Part 273 | Yes | Yes | marked, with the footnote for states that adopted aerosol cans before the federal rule was promulgated | Electronic devices and electronic components |
Read that table as an instruction to go check something, and not as a legal conclusion about Kansas, Nebraska or Oklahoma. This work read EPA’s table and the federal rule. It did not read those three states’ rule text, and the state rule is the only document that answers the question. The check takes an afternoon: pull your state’s universal waste citation from the column above, find the list of covered wastes in it, and confirm whether aerosol cans appear before your facility manages a can drum on the universal waste track. Where they do not appear, the can is a fully regulated hazardous waste under the state program, with the generator clocks, the manifest and the category math the universal waste track would have removed.
Missouri adopted the rule and is not authorized for it
Missouri is the one row showing Adopted “Yes” with Authorized “No.” The state has universal waste requirements in its own code at 10 CSR 25-16.273, and EPA has not authorized that rule into the state’s approved program, which leaves the federal requirement independently in force and federally enforceable. A Missouri facility is answering to two texts, and a program written against only the state citation has a federal exposure it never addressed. EPA’s page describes the general mechanics for jurisdictions without authorization: federal universal waste rules “went into effect immediately upon the federal effective date in states and territories that are not authorized,” naming Iowa and Puerto Rico, with Iowa’s hazardous waste program administered by EPA Region 7. For an operator with plants in Kansas City, Missouri and Kansas City, Kansas, that is two programs across one metro area.
Colorado and Nebraska add electronics, and Texas adds paint
The federal rule is a floor, and the second direction is the one corporate standards miss. Colorado’s program adds electronic devices and electronic components, Nebraska’s program adds Electronics, and Texas adds paint and paint-related wastes. None of those streams exists in the five-stream federal list at 273.1(a). The federal list is not fixed either: EPA states on its universal waste page that it is planning to propose rules for end-of-life solar panels and lithium batteries, with no date announced. An operator that standardized on the five federal streams is under-collecting in Colorado, Nebraska and Texas, where streams the state treats as universal waste are managed as something else, and potentially over-claiming in Kansas, Nebraska and Oklahoma on cans. Both errors come from writing one corporate procedure against the CFR and sending it to every plant.
What happens when a universal waste container leaks?
273.17 and 273.37 require the handler to immediately contain all releases of universal wastes and residues. Any hazardous waste generated from the release is then managed under 40 CFR parts 260 through 272, with the handler as the generator under Part 262. The universal waste track does not cover the spill residue.
A cracked lamp, a battery that vents, a thermostat with a broken ampoule or a can that fails produces residue governed by the full generator rules, which means a waste determination, a container carrying the Hazardous Waste marking and an accumulation date, and the generator clock rather than the one-year universal waste clock. The management standards at 273.13 and 273.33 exist to prevent that: batteries with leaking or damaged cells in closed, structurally sound, compatible containers; pesticides in a closed structurally sound container, an overpack, a Part 265 Subpart J tank, or a closed transport vehicle or vessel; mercury-containing equipment with leaking, damaged or unencapsulated units in closed containers designed to prevent mercury escape; lamp packages structurally sound and closed so breakage is prevented, with broken lamps containerized immediately; and aerosol cans in a structurally sound container protected from heat, with leaking cans packaged separately, overpacked with absorbent, or punctured and drained. A clean-up kit at the accumulation area is what makes “immediately contain” achievable on a Saturday night shift.
What is the penalty exposure for a universal waste violation?
40 CFR 19.4 Table 1 sets the RCRA section 3008(g) maximum at $93,058 and the 3008(a)(3) maximum at $124,426 for penalties assessed on or after January 8, 2025. 42 U.S.C. 6928(g) makes each day of violation a separate violation, which is how a labeling finding becomes a multiple.
No EPA enforcement case citing 40 CFR Part 273 with a published penalty figure was located for this piece. EPA’s civil and cleanup enforcement case listings carry RCRA entries with no Part 273 citation and no dollar figure in the listing text: Denka Performance Elastomer, Chemours, Stericycle, J.R. Simplot and PCS Nitrogen all read that way. ECHO’s enforcement case search loads but cannot be queried by fetch. There is no universal waste enforcement trend to report here, and a count assembled out of adjacent RCRA cases would not be one.
The exposure argument rests on the penalty structure instead. 40 CFR 19.4 Table 1 lists $124,426 for RCRA section 3008(a)(3), $93,058 for 3008(g) and $74,943 for 3008(h)(2), all for penalties assessed on or after January 8, 2025. Table 1 has no 2026 column. That January 2025 column is the latest one, it shows no end date, and the section’s own amendment timeline ends there, so those are the operative figures going into 2027. Table 1 also prints bare numbers with no unit text, and the unit comes from the statute. 42 U.S.C. 6928(g) authorizes a penalty for “each such violation” and states that “Each day of such violation shall, for purposes of this subsection, constitute a separate violation.” 6928(a)(3) reads “per day of noncompliance for each violation of a requirement of this subchapter,” and 6928(h)(2) reads “for each day of noncompliance with the order.”
A missing label, a missing accumulation date and an undocumented training conversation are each a violation of a requirement of the subchapter, and each day each one persists is a separate violation. An adjacent case shows the arithmetic without being this part: in the Oregon Tool Inc. matter, Kansas City, Missouri, docket RCRA-07-2023-0120, total penalty $337,253, one count rested on two unlabeled four-quart containers of used oil. That is a used oil case under 40 CFR Part 279 and not a Part 273 case. The shape of the finding is identical, a two-word marker missing from a small container.
What to Check This Week
- Add up the five streams as one number and find the peak. 273.9 measures collectively and at any time. Look at what was on site during the last lighting retrofit or battery changeout rather than at what is on site today. If the peak crossed 5,000 kilograms this calendar year, the facility is a large quantity handler now.
- Pull your state’s universal waste citation and read the list of covered wastes in it. The table above gives the citation as EPA prints it. Kansas practitioners start at KDHE’s waste program and the citation at 28-31-15 and 28-31-273. Confirm whether aerosol cans appear before any can drum goes on the universal waste track, and whether your state adds a stream the federal list does not have.
- Walk the accumulation area and read the containers out loud. The words have to match 273.14 or 273.34. Then pick one of the six 273.15(c) date-proof methods and retire the partial systems around it.
- Reconcile the training population against the people who touch the material. If the facility crossed the handler line this year, 273.36 applies for the rest of the year.
Reading a state universal waste citation against what is actually standing in the accumulation area is a half day of work, and it is work iSi does. Environmental compliance audits, written waste program development and the training the two handler standards call for are standing capabilities here. The delivery options are a project engagement through environmental compliance or the ongoing program under the EHS COOP, where the state program check becomes part of the recurring cycle. Either way you get a response back the same day.
Frequently Asked Questions
What are the federal universal waste categories?
Five: batteries, pesticides, mercury-containing equipment, lamps, and aerosol cans, the last added by the 2019 rule.
Is the aerosol can category actually law in Kansas, Nebraska and Oklahoma?
No. Adding aerosol cans made the federal rule less stringent, so authorized states were never required to adopt it. EPA’s state program table, updated October 8, 2026, marks the aerosol can column for Missouri, Texas and Colorado and leaves Kansas, Nebraska and Oklahoma blank. Verify the state citation before managing aerosol cans as universal waste.
What must a universal waste container be labeled?
Each container or device must be labeled or marked clearly with the universal waste designation 40 CFR 273.14 specifies for its waste type, and the handler must be able to demonstrate how long it has been accumulating.
How long can universal waste accumulate on site?
One year from the date it was generated or received, with a documented start date. Holding it longer is allowed only when it is solely to accumulate quantities necessary for proper recovery, treatment or disposal, and the handler bears the burden of proving it.
Sources
- 40 CFR Part 273, Standards for Universal Waste Management (eCFR, current as of 10/23/2026): https://www.ecfr.gov/current/title-40/chapter-I/subchapter-I/part-273 (verified 2026-11-12)
- 40 CFR 19.4, Civil Monetary Penalty Inflation Adjustments, Table 1 (eCFR, current as of 10/22/2026): https://www.ecfr.gov/current/title-40/chapter-I/subchapter-A/part-19/section-19.4 (verified 2026-11-12)
- 42 U.S.C. 6928, RCRA federal enforcement (govinfo U.S. Code): https://www.govinfo.gov/link/uscode/42/6928 (verified 2026-11-12)
- 84 FR 67202, Increasing Recycling: Adding Aerosol Cans to the Universal Waste Regulations, FR Doc 2019-25674, RIN 2050-AG92, effective 2020-02-07 (govinfo PDF): https://www.govinfo.gov/content/pkg/FR-2019-12-09/pdf/2019-25674.pdf (verified 2026-11-12)
- Federal Register, Increasing Recycling: Adding Aerosol Cans to the Universal Waste Regulations: https://www.federalregister.gov/documents/2019/12/09/2019-25674/increasing-recycling-adding-aerosol-cans-to-the-universal-waste-regulations (verified 2026-11-12)
- EPA, Universal Waste (updated 2026-09-18): https://www.epa.gov/hw/universal-waste (verified 2026-11-12)
- EPA, State Universal Waste Programs in the United States (updated 2026-10-08): https://www.epa.gov/hw/state-universal-waste-programs-united-states (verified 2026-11-12)
- EPA, Increasing Recycling: Adding Aerosol Cans to the Universal Waste Regulations, docket EPA-HQ-OLEM-2017-0463: https://www.epa.gov/hw/increasing-recycling-adding-aerosol-cans-universal-waste-regulations (verified 2026-11-12)
- EPA, Civil and Cleanup Enforcement Cases and Settlements: https://www.epa.gov/enforcement/civil-and-cleanup-enforcement-cases-and-settlements (verified 2026-11-12)
- Kansas Department of Health and Environment, Waste (state citation 28-31-15 per EPA’s table): https://www.kdhe.ks.gov/168/Waste (verified 2026-11-12)
- 60 FR 25542, May 11, 1995, the original universal waste rule, cited as the promulgation date carried in the eCFR source note for 40 CFR Part 273